Routerboard.com

	PCI Riser Card RouterBOARD 71 (IA/PP1)
	The PCI Riser Card RouterBOARD 71 is custom designed for the RouterBOARD 200 series to allow positioning the PCI standard card horizontally in RouterBOARD 200 series routing equipment. The card is suitable for PCI cards complying to the PCI 2.1 and 2.2 standards. Note: the Riser Card can not be used with RB/INBOX and 3C/INBOX! Schematic Drawings of RuterBOARD 71

48v 30w Power Adapter + Power plug (48POW)

The AC/DC switching mode Power Adapter provides 30 Watts of continuous output power. The Power Adapter is UL 94V-0 compliant and includes IEC-320-C14 input for worldwide applications. It meets FCC class B and CISPR class B emission limits and is designed to comply with UL, C-UL, TUV and CE requirements. All units are 100% tested.

Specifications:

Input Voltage	90 - 264 VAC
Input Frequency	47 - 63 Hz
Output Power Range	0 - 30 W
Output Voltage	48v DC
Output Current	0.50 A
Input Current (Low Line)	0.7 A
Input Current (High Line)	0.46 A
Low Line Inrush Current	12 - 15 A
High Line Inrush Current	26 - 30 A
Efficiency	65 - 85 %
Line Regulation	0.5 - 1 %
Load Regulation	3 - 5 %
Transient Response	4 ms
Hold-Up	12 ms
Total Regulation	2%
Start Up Time	0.3 - 2 S
Ripple & Noise (Peak to Peak)	0.5 - 1 %
Safety Ground Leakage Current	0.5 - 0.75 mA
Temperature Coefficient	-0.04 - 0.04 %/°c
Dimensions (without cable)	640 x 103 x 30 mm

64 MB CompactFlash - Blank (64/CLB)

The CompactFlash cards for information storage offer AND architecture, 3.3 and 5 volt compatibility, shock resistance, and low power requirements. These high performance cards feature fast read and write speeds at up to 1.5MB/sec. The CompactFlash card data is protected by built-in dynamic defect management and error correction technologies.

Specifications:

Type	Type I
Capacity	64 MB
Voltage	5V ± 10% or 3.3V ± 5%
Operating Temperature	0° C to 60° C
Operating Shock	2,000 G max.
Operating Vibration	15 G
Humidity	5°C to 96% RH
Altitude	Up to 50,000 ft.
Dimensions	42 x 36 x 3 mm

64 MB CompactFlash with RouterOS Basic License (SW/CL3 )

This is the discription of MikroTik RouterOS Base Licence. For Compact Flash specifications, see above.

MikroTik’s software product, MikroTik RouterOS, is a router system which makes it easy for any ISP or network admin (anybody who can install an operating system) to make a PC router for wireless, wide area, or local area networks. This dedicated router software system uses the well-tested Linux kernel to provide high-reliability. Administration is made by web with remote GUI console (WinBox), Telnet, or Serial Console. Many commonly used high-speed interfaces are supported. The software is currently used by wireless ISPs all over the world.

Specifications:

Routing	RIP v1 / v2, OSPF v2, BGP v4; Equal cost multi-path routing; Policy based routing; firewall marked packet routing
PPP	ISDN, RADIUS, PPTP, PPPoE, modem pool
IP telephony	Voice over IP protocol support
Bridging	Spanning tree protocol; multiple bridge interfaces; bridge firewalling
Stateful Firewall and NAT	Packet filtering; source and destination NAT; classification by source MAC, IP addresses, ports, protocols, protocol options, interfaces, internal marks, content, matching frequency
VLAN	Virtual LAN 802.1q protocol support
DHCP	DHCP server per interface; DHCP client
HotSpot	HotSpot Gateway with RADIUS authentication/accounting
Universal Client	Transparent address translation not depending on the client's setup
Monitoring/Accounting	IP traffic accounting, firewall actions logging
Tunnels	IPIP tunnels, EoIP (Ethernet over IP)
IPsec	IP encryption (IP security)
Data Rate Management	Per IP / protocol / subnet / port / firewall mark; HTB, RED, SFQ, byte limited queue, packet limited queue; hierarchical limitation, CIR, MIR, contention ratios
Tools	Ping; traceroute; bandwidth test; ping flood; telnet; SSH; packet sniffer
DNS	Name resolving for local use; Dynamic DNS Client
NTP	Network Time Protocol server and client
SNMP	Read-only access
Remote administration and upgrading	Web/GUI, Terminal Console, Telnet, Serial terminal console, FTP, Remote upgrading by uploading the software packages to the router

For more features and MikroTik RouterOS software documentation, please see the http://www.mikrotik.com/documentation.html

For purchasing the MikroTik RouterOS, please see
http://www.mikrotik.com/software.php

Indoor Case for RouterBOARD 230 (3C/INBOX )

Indoor case for RouterBOARD 230 with holes for serial port, USB port, power supply, two ethernet ports And three holes for N-Female bulkhead connectors.

Dimensions

258 x 110 x 38 mm

Schematic Drawings of Case

Big Indoor Case for RouterBOARD 230 (RS/INBOX)

Indoor case for RouterBOARD 230 with holes for serial port, USB port, power supply, two ethernet ports and four holes for N-Female bulkhead connectors. Made especially for use with the RouterBOARD 71 Riser card - more interfaces, same quality.

Dimensions

252 x 133.2 x 76.4 mm

Schematic Drawings of Case

Outdoor Case for RouterBOARD 230 (RB/OUTBOX)

Waterproof case for RouterBOARD 230 for outdoor installations.

The clamps supplied with the equipment fit poles between 50 mm and 70 mm in diameter. If this clamp does not meet your needs, there are commercially available kits that allow the mounting of the unit to a pole of any diameter.

Security Standard	IP 66
Dimensions	180 x 254 x 89 mm
Material	Polycarbonate
Color	Light Grey
Operating temperature	-40 C to 120 C